12W 200..350mA 9-40V DALI 2.0 Himmennetävä LED Vakiovirtalähde

DALI-2 HIMMENNETTÄVÄ LED VAKIOVIRTALÄHDE - ALCC012-00350-040-DALI-SR

OMINAISUUDET

• Yksikanavainen, virta valittavissa DIP-switch painikkeilla

• DALI Protokolla IEC 62386-207 Ed2.0

• Tukee Touch-DIM ominaisuutta

• Sisäänrakennettu aktiivinen PFC -toiminto

• Todella tasainen himmennys, ei valon flickeröintiä (valo ei vilku)

• Suojaukset: Oikosulku, ylikuormitus

KÄYTTÖKOHTEET

• Soveltuu sisätilojen LED-valaistukseen, kuten esim. alas- ja kohdevalaisimiin

IP luokitus

IP20

Vakiovirta

200mA

250mA

300mA

350mA

OUTPUT

DIP Switch Technical Values

• 200mA 9-40V 8.0W
• 250mA 9-40V 10.0W
• 300mA 9-40V 12.0W
• 350mA 9-34V 11.9W

Channel: 1
No load output voltage: 50V Max
Current Tolerance: ±5%
Ripple Current: <3%
Turn-on delay time: <1s @230VAC

INPUT

Voltage: 220VAC-240VAC
Frequency Range(Hz): 50/60Hz
Efficiency: 80%@230VAC,Full load
Power Factor: ≥0.95@230VAC,Full load
THD(full load): <10%@230VAC, Full load
AC Current Max: 0.07Amax@230VAC
Standy Power: <0.5W
Inrush Current: Cold start,18A (twidth=14us measured at 50% Ipeak) @230VAC

PROTECTIONS

Short Circuit: Close output recovers automatically after fault removed.
Over Load: When the output voltage is exceeded, the output current decreases and, recovers automatically when the load is reduced.

DIMMING

Dimming Type: DALI /Touch DIM
Dimming Range: 0.1%-100% Dimming to off

ENVIRONMENT

IP rating: IP20
Working temp. humidity: -20 ~+50°C
Storage temp.: -40 ~+85°C ; 20-90%RH
Tc.: +90°C

DIMENSIONS

Lenght: 150mm
Width: 43mm
Height: 29mm
Weight: 125g
Material: PC
Carton Size 50PCS/Carton; 6.5kg±5%/Carton; Carton Size: 319*254*136mm(L*W*H)

SAFETY

Surge: L-N:1kv
Withstand Voltage: I/P-O/P: 3000VAC/1min/5mA
DALI Standard: IEC 62386-101: 2014, IEC 62386-102: 2014; IEC62386-207 Ed 2.0
Safety Standards: EN61347, GB19510
EMC Emission: EN55015, EN61000-3-2
EMC Immunity: EN61000-4-2,3,4,5,6,8,11; EN61547

WARRANTY and LIFETIME

Lifetime: 50,000h@tc:70
Switch Cycle: >100,000 times
Warranty: 5 years

CAUTIONS

1. This product should be installed by qualified personnel.
2. This product is non-waterproof, need to avoid sun and rain. In case of outdoor use, please ensure it is mounted in a waterproof enclosure.
3. Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4. Please make sure LED power supply output voltage, current is used to meet the product requirements.
5. Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6. Due to safety concerns, PVC or rubber cord of 0.75-2.5mm2 is recommended for input and output terminal(s) (excluding signal terminals). Flat power cord is not suitable. Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
7. In case of malfunction, do not repair it yourself.