40W 500..850mA 9-48V DALI 2.0 Himmennettävä Vakiovirtalähde

AURA+ ALCC040 LED DRIVER SARJA

Pienikokoinen vakiovirta LED virtalähde DALI 2.0 himmennyksellä, DIP-SWITCH virtavalitsimet - ALCC040-00850-048-DALI

OMINAISUUDET

• Pieni kompakti koko
• DALI-2 and Push DIM Himmennys
• Yksikanavainen, Ulostulovirta valittavissa DIP Switch valitsimilla
• Laaja tulojönnitealue 120VAC-277VAC
• Himmennysalue 0,1%, tasainen himmennys ilman flickeröintiä
• Flicker Free
• Puoliksi potattu
• IP20 (On käytetty ilman ongelmia myös vaativimmissakin olosuhteissa)
• Johdollinen

KÄYTTÖKOHTEET

• Alasvalot, paneelivalot, spottivalot, kattovalot, kaluste- ja design-valaisimet, lattiavalot, track-valot ja teollisuusvalaisimet

IP luokitus

IP20

Vakiovirta

500mA

550mA

600mA

650mA

700mA

750mA

800mA

850mA

Liitäntä

Johdoilla

OUTPUT

DIP Switch Technical Values

• 500mA 9-48V 24W
• 550mA 9-48V 26.4W
• 600mA 9-48V 28.8W
• 650mA 9-48V 31.2W
• 700mA 9-48V 33.6W
• 750mA 9-48V 36W
• 800mA 9-48V 38.4W
• 850mA 9-47V 39.95W

Channel: 1
No load output voltage: 58V Max 58V Max
Frequency: 1KHz Min PWM
Current Tolerance: ±5%
Ripple Current: <3%

INPUT

Voltage: 120VAC-277VAC
Frequency: 50/60Hz
Efficiency: 87%@120VAC, Full load 87%@120VAC, Full load
PF: >0.99@120VAC, Full load
THD(full load): <10%@120VAC, Full load
Current: 0.6A max @120VAC
Inrush Current: Cold start, 30A@120VAC

Protections

Over Voltage: Hiccup, recovers after fault condition is removed
Short Circuit: Hiccup, recovers after fault condition is removed
Over load: Close output, recovers automatically after fault removed

Dimming

Dimming type: DALI/Touch DIM (Push DIM)
Dimming range: 0.1%-100% Dimming to off

Environment

IP rating: IP20
Working temp.: -20 ~+50°C
Tc.: +90°C
Relative humidity: 20~90% RH

DIMENSIONS

Lenght: 121mm
Width: 44mm
Height: 26.5mm
Lenght of the wires: 150mm
Stripping Length: 10mm
Weight: 156g
Packing Size: 50pcs
Material: PC

Safety

Surge: L-N:1KV
Withstand Voltage: I/P-O/P: 3000VAC/1min/5mA; I/P-Gnd: 1500VAC/1min/ 5mA; O/P-Gnd: 500VAC/1min/5m
Safety standards: UL8750/UL1310/CSA25013,CSA class P
EMI Eission: EN55015,EN61000-3-2 Class C,IEC61000-3-3
EMC Immunity: FCC class B(120V)/class A(277V)

Push DIM Function
1. Press the Touch DIM (Push DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Touch DIM (Push DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Touch DIM (Push DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Touch DIM (Push DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing Push DIM switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.

Cautions
1. This product should be installed by qualified personnel.
2. This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure. Good heat dissipation conditions extend product life.Please install the product in a well-ventilated environment.
3. Please make sure LED power supply output voltage, current is used to meet the product requirements.
4. Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
5. Due to safety concerns, PVC or rubber cord of 0.75-2.5mm2 is recommended for input and output terminal(s) (excluding signal terminals). Flat power cord is not suitable.Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
6. In case of malfunction, do not repair it yourself.